#Fanuc 21t parameter manual code
#Fanuc 21t parameter manual series

Sequence Number Increment Amount = Parameter # 3216ДЇanuc 16/18/21/I-series -Parameter 6 from 0 to 1ДЄllow axis movement when stopping spindle. Sequence Number Increment Amount = Parameter # 32ДЄdd Sequence Numbers Automatically = Parameter #0000 bit 5(6th digit from the right) set to 1. Sequence Number Initial Value = Parameter #31 Hold Shift for 5 seconds to capture screen.ДЄdd Sequence Numbers Automatically = Parameter #10 bit1 (2nd digit from the right) set to 1. Mitsubishi Edit 9000 programs change par.1121 to 0, and check 1122 should be 0 to display them.ДЇanuc Insert ATA card, MDI mode, Set I/O device to 4 for using card.

#Fanuc 21t parameter manual code

Multiple M-codes to in one line parameterДЇanuc 16/18/21/16i/18i/21i-Parameter 3404.7 from 0 to 1 (enables up to 3 M-codes but has some restrictions depending on the M-codes used together)ДЇanuc 16/18/21 & 16i/18i/21i-Parameter 3202 (NE9 will be above the proper bit #) (6079-6089 can be assigned an m-code or G code to call up the sub programs) (Parameter 6080=program #9020, 6081=9021, 6082=9022 ETC.) Fanuc-O control 10.4(PRG9). Be careful to select the right switch usually mounted in tape box area. If not page up multiple times to get to the top.ДЇanuc 3 and some older controls- Turn rotary switch to 1. Yasnac- LX1 to LX3, MX1 to MX3 control- Change rotary switch by tape reader from 0 to 1, or parameter 6219ДЇanuc 16,18,21 and 16i/18i/21i- offset settings hard key, press settings softkey, should be on top of screen. Mitsubishi controls- Press system hard key then press parameters, press setup softkey, answer yes to question then select the soft keys such as base (1000's par.) or PLC (6400's par) or whatever to get to desired set of parameter numbers

You will see two soft keys under the display screen in the edit mode that look like parenthesis Parameter 3204 bit 2 Labeled EXK (check in your list of parameters for confirm this function before changing.

#Fanuc 21t parameter manual series

Getting Parentheses on 16 and 18 series Fanuc controls parameter Mitsubishi (Meldas 65, may work for others) control parameter 6309- set to 100 (100=RPM)ДЇanuc 16/18/21- Fanuc Gdata par. out.ДЇanuc 16,18, Set speed, 6306 same value,3005 same valueДЄlarm when spindle/chuck is spun by hand during setup. If in envelope must turn off first before handwheel. Turn on parameter 1310.0 for X,Y,Z axes Set the machine coordinates in Parameters 13 to enclose a box around the area to inhibit or only allow machining inside All other related parameters are 1300-1327. G-codes to turn on or off controlled area G22(on),G23 (off). (Fanuc 16,18,21 and 16i/18i/21i)- enables an inhibited area or work envelope for fixture. Stroke check or inhibit work area parameter Mazak parameters/ mitsubishi parameters cheat sheet If you get answers please Email me so I may include them on this page.ДЇor a nice chart of common Parameter changes and G-codes see below If your machine parameters are not listed here, check if it is possible with the builder or post in a forum to get some help. Parameter list for programmers/applications when setting up and programming a CNC machine tool.